• Content Count

  • Joined

  • Last visited

  • Days Won


sarah last won the day on August 7 2019

sarah had the most liked content!

1 Follower

About sarah

  • Rank

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Hi Mark. Thanks, the information was Originally collated for my articles printed in collectors magazines, such as The Train Collectors Society, and The Tri-ang Society.
  2. Hi. It is R.449. The running number is also the R. Number in this case. It looks like the easiest way to replace the balcony rails would be to make them from plastic card. It will be hard to find these parts, though you may be lucky, as not many would know what the part is if on it’s own. Be aware that the R. Number R.449 has been reused for the Hornby Railways Coach Lighting Unit, to fit to certain Hornby coaches. Also a LNER “teak” finish brake Clerestory coach, using the Tri-ang GWR Clerestory coach tooling.
  3. Yes, both of these used the Seuthe type smoke units. The later Synchrosmoke units were only used in locomotives.
  4. Tri-ang Railways, Tri-ang Hornby, Hornby Railways and Hornby locomotives all come originaly with an instruction sheet, which have basic maintenance guides for the locomotives of the time the Instruction Sheet or book was printed. These can be obtained, to replace original lost ones, from various sources. Ringfield Motors.... Type 5 and 6, 1989. The first type of Tri-ang Hornby / Hornby Railways Ringfield Motor. Type 1.
  5. Hi Kev. Thanks. The crew are from a Bachmann pack. There are currently two packs containing Steam era locomotive department type figures. 1950s Train Crew Bachmann Model 36-407 Scale: OO (1/76) Locomotive staff Bachmann Model 36-047 Scale: OO (1/76) Some really good figures. Some can be modified, by removing oil cans, cleaning rags, wheel hammers, etc. for more general use. Some have the arms as seperate mouldings, glued into place. These can be removed and replaced differently if required....
  6. Hornby Terrier, the new version. R3767. BR Lined Black, Early Crest. 32655 (Stepney). General views.... after I had installed a loco crew, and changed the colour of the reverser lever and regulator.... and the gauge glasses. The extra pipes, which fit under the buffer beams.... Initial modifications.... All locos deserve a crew! The gauge glasses look better (IMO) in white than "Copper" or "Brass", and the Reverser is not likely to be made of Brass or Copper, as it would likely bend! (It is coloured "Copper" or "Brass"as it comes. The Regulator is plain black as it comes.... I prefer it in red! Getting into the cab....body dis-assembly. The body, boiler, side tanks, cab and bunker, are held onto the metal footplate by 7 screws. one into the smokebox, two each side into the side tanks, and two into the cab/bunker. The cab seems to be clipped to the boiler, but there are a few pipes from the boiler that are probably glued into the holes in the cab front.... I did not try to part the cab from the boiler as I did not relish trying to get the pipes back into their holes, even if they were not glued in! DCC Decoder Fitting. The 6-Pin socket is in a position that precludes the use of most, if not all, direct plug 6-pin decoders. The Hornby R7150 6-pin decoder has a short wire harness and 6-pin plug. The wires are just about the maximum length that can be folded over the decoder, and still fit inside the body. Some insulating tape is a very good idea to cover the exposed connexions, and prevent the decoder coming into contact with any metal.... It is one of very few 6-pin decoders that can be fitted, it would seem.... I have got the Hornby decoder, and fitted it to mine. Less hassle for me. Couplings. I have fitted Kadee NEM couplings to my Terrier. #19. The NEM pockets on the Terrier are at the correct height when seated properly, but the Kadee couplings require packing under the shaft inside the pockets, otherwise they are a bit of a loose fit and droop. Coupled to a Hornby Ex LNER Class O1 tender chassis....again the NEM pocket is at the correct height....
  7. Wishing you all a happy new year... as we pass (later, but I may well be asleep by then! ) from 2018 into 2019!
  8. Wishing you all a happy Christmas. I hope you all have a good time... we will be doing our best here! ;)
  9. The Waverley is a very nice ship... and was built for the London & North Eastern Railway Company! The current livery is basically the LNER livery... We went on a trip from Newhaven to Off Dugeness via Eastbourne Pier and Hastings Pier in both directions, and around the Royal Sovreign Light Tower (which replaced a Lightship) on the return from Eastbourne Pier to Newhaven. It was a long day, but utterly fascinating, and I can still hear the "drumming" of the paddle wheel floats in my mind, yet alone the whistle and hooter! That was quite a few years ago now...
  10. Something I have been working towards for some time now... A model of the Brush Type 4 Co-Co (Class 47) D1677 named 'THOR'... This was actually the second '47' to receive the nameplates August 29th 1966), as the first, D1671 (September 1965), was scrapped after being involved in a fatal accident on the night of December 16th/17th 1965 , involving derailment by a landslip and susequent collision with a Class 37 (EE Type 3 Co-Co), D6983, which was also scrapped... D1677 was later numbered 47 091 (1974), then 47 647 (1986), then 47 846 (1990) This is a Lima body (Lima L204633) in BR Two tone green with yellow front and canb windows, on a Hornby Railroad chassis, with TTS DCC Decoder fitted. The nameplates are from Modelmaster. I have removed the old numbers, 47 369 and backdated the cab areas into Yellow Panel livery, from the Yellow end and windows. The new numbers are 'Wolf' rub-down from Modelmasters... a pity there wasn't a complete number for D1677, it was fun! I have also cut out the headcode boxes, and drilled out the tail lights... and fitted a driver in each end. Lighting is a distinct possibilty... sometime! ;) The headcodes are temporary ones, from an old Hornby Class 37 sheet... Couplings are Kadee NEM, #18 or #19 I think...
  11. Oxford Rail 6 Wheel 'Toad' Later Plated Version...Modified The Later 'Plated' versions of the Oxford Rail GWR 'Toad' Brakevans have a few small problems... The plating does not extend to the ends... The 'rear' window is wrong. (Being apparently based on a preserved Toad with modifications!) There are two lamp irons on the 'rear' sides, that should not be there. (Very early Toads had hatches in the sides to allow side lamps to be placed on these lamp irons, but the model does not have the hatches... which were done away with by the GWR anyway!) Dismantled Toad...there are two screws under the NEM pockets. The body is a bit awkward to remove, as the spigots of the buffers protude through the buffer beams, and get in the way of removing the body...the body is also a very good fit onto the base... But with much struggling I succeeded in parting the parts from each other! The base, whch has some details, which are basically invisible when assembled. The representation of the stove is not very good though! The body inside...the partition is not glued in place, so can be removed easily... Chassis underside, shewing the screw holes ....access will usually involve removing some ofthe delicate brake rodding! The 'rear' window and the side windows,are one piece of clazing, glued in place. The large 'wrong' window was cut out very carefully from the two side windows. The window framing was cut out very carefully, and the framing around the outside of what should in fact be a hatch to allow acess to the 'rear' lamp bracket, made good. I used a new Hornby GWR Toad model to copy the details! The two side windows were kept to one side, to be re-fitted after painting... The hole was patched on the inside with a plasticard patch, slightly bigger than the hole. The hatch was made from plasticard scribed for planking, and glued into the hole. Plating on the 'rear' was added using plasticard, again the Hornby model was used as a pattern... unfortunately, I got two thicknesses mixed up, and the 'rear' plating was made too thick... and I didn't notice until it was glued in place! Some rivet detail was added by using a pointed tool on the 'inside', using the Hornby Toad as inspiration! The 'rear' lamp iron needed moving. The actual iron is metal, 'L' shaped, and fits into a hole. The base of the lamp iron is moulded into the this needed carving off, and a new hole and lamp iron base added to the plating... The two 'rear' side lamp irons were removed, lamp iron bases carved off, and the small holes filled. The 'front' or veranda end was plated in the same way... but I used thinner plastic card this time! A representation of the lever to operate the 'rear' sandboxes mounted on the veranda side of the partition was made from a piece of wire, painted with a white end. Also, some plastic strip and rod was used to make a representation of the veranda end sanbox operating lever and rods...Again copied from the Hornby model... The result is not in any way perfect, as the framing should be on top of the plating... but I think it looks a bit better than planking? The body was re-painted BR unfitted stock grey, as there was a small diffeence in the colour applied by Oxford Rail. New lettering (Croes Newydd) and numbers to be added... and the small holes need a little more filling...
  12. Dapol and Hornby OO Gauge Terriers… Some Model Rail Magazine Terrier Coverage... Issue 40 FEB 2002. Pages 34 - 42 Real and Model. Full details. Class History 1872 - 2002. Improve the Hornby Model. . Prototype and model photos. Extending the bunker Isle of Wight Style. A1X front sandbox removal. A1 Smokebox Wingplate construction. Alan Gibson cast brass Salter Safety Valves. Issue 246 APRIL 2018. Loco Spotlight Stroudley's 'Terriers' Part 1. Getting closer to classic locomotives. Pages 80-85. Class history. List of preseved locos. List of building dates and basic specifications. Side view of "Knowle" with some basic dimensions added. 5 small photos shewing livery variations from LBSC IEG to BR Lined Black. Prototype photos including some detail photos of "Boxhill" (NRM) as A1. amd BR liveried "Knowle" (Kent & East Sussex Railway) as A1X. No actual modeling features, pure prototype information. Issue 248 JUNE 2018. Loco Spotlight Stroudley's 'Terriers' Part 2. (The Locos sold by the LBSCR) Pages 88 - 93. Pages 88/89 Introduction and large photo of "Freshwater", W8 in Southern Green at IOW Steam Railway. Pg. 90. Details of 6 destinations. 3 small BW pics, (K&ESR, L&SWR & SECR) and one colour pic (Newhaven Harbour. Fenchurch 1958). Pg.91. Details of 4 destinations. 3 B/W pics. (S&MR, WC&PR & EHLR). Reccomended Reading. What's Next (Details of Part 1backnumber!). Pg.92. "Second-hand 'Terrier' walk-round". 7, mainly detail pics, of BR 32670 (Ex K&ESR, with unique modified bunker...) Pg. 93. Isle of Wight.The IOW Terriers. 2 BW photos, inluding 1 with Stroudley type coach set 49 (Both 1936). List of details of IOW Terriers. Photo Below: 32670 is a Hornby model. It represents a loco that was sold to the Kent & East Sussex Railway (Where it was re-boilered, and had a unique extended bunker, not modelled, fitted.). The loco was later, after Nationalisation, transferred to the Hayling Island Branch. It is now preserved, back on the K&ESR!. "Stepney", No.55, is a Dapol Model. It now (after minor modifications) represents the loco as preserved on the Bluebell Railway, where it was re-painted into LBSCR livery, but in A1X condition, vacuum braked only, with no Westinghouse air brake pump. Link to a photo of "Fenchurch", No.672 in a "Brighton Works" livery. (2012) This loco has been restored to represent later A1 condition. The Dapol (& now Hornby) model is a hybrid, with A1X sandboxes on the chassis, and an A1 length smokebox (some models have a spacer ring pre-fitted at the factory to lengthen the smokebox to A1X length.). The models also have A1 (pre-re-build) splasher mounted sandboxes, the "vents" on the tank tops (from the A1 condensing system I believe), but no "wings" on the front of the smokebox/sandboxes on the footplate. Most models seem to be fitted with the added Vacuum braking ejector pipe, which runs from the cab front to the smokebox, as well as a Westinghouse Air Brake pump on the eight hand cab side, but only have one brake pipe fitted, which looks more like a Vacuum brake pipe than an Air Brake pipe… With the locos when new is a bag of parts, which can, with some modification to the base model, be used to convert the locos to other varieties. There is a pair of pipes, which are the condensing system pipes, which run from the top of the tank fronts into the sides of the smokebox (Copper coloured on Boxhill, see the recent Model Rail article). There is a plain (not Salter Safety Valves) boiler dome, and a set of Ross Pop type safety valves. I, would assume these are for one of the "sold on" locos... There is a spacer ring to lengthen the smokebox to A1X length. This fits onto the smokebox front, after this has been carefully removed (the glue bond can be strong!) from the boiler. The smokebox front mounting flange is long enough to go through the ring and still locate into the boiler. There is a set of coal rails, with a coal load moulded in. This is the simplest part to fit, as it locates into the top of the coal bunker Fitting the A1X smokebox extension ring. The smokebox front can be pretty well glued in place. It needs careful persuasion to part the glue bond. There is a small location pin on the bottom of the smokebox front, which locates into a slot in the bottom of the boiler. When the smokebox front finally surrenders, it may well be found easier to fit the extension ring over the location flange of the smokebox front with the handrail removed. The location pin on the smokebox front locates into the cut out in the extension ring. The two recesses are designed to clear the handrail knobs, but may prove too shallow. I glued the extension ring to the smokebox front, and when the glue had set hard, drilled out the handrail knob locations with a small drill, before gluing the handrail back in place. (The first attempt I made, without drilling the holes out a bit, the handrail knobs pushed the extension ring away from the smokebox front!) It will be noted that there is now no positive location pin to align the smokebox front onto the boiler! This is where care and attention will be needed when gluing the smokebox front to the boiler, to get the hinge vertical… If you are going to remove the splasher sandboxes, do not glue the smokebox front into place yet! Speaking of “vertical”, the lower handle on the smokebox door should point vertically Down, as this is the catch handle. The model comes with this handle at the “twenty-five to “ position! I carefully carved the handle away from the bottom, meeting with a cut across the top at the centre boss. I then re-glued the removed section in the correct place! I have removed the weight from the boiler (held in by a screw from underneath) and made a hole from the boiler to the motor area by chain drilling around the inside of the boiler from the smokebox end. This makes an access to the boiler from the motor area when the smokebox front is re-attached. I have not yet reattached the smokebox front; it is at present just slotted into place. I have yet to fit a DCC chip, and may need access! Removing the A1 splasher mounted sandboxes. The front splasher sandboxes need to be removed. This is not so easy, as the earlier Model Rail article found. I worked out that there are a couple of places where it is not so dangerous to cut with a fine razor saw. Cut 1 is across the diagonal from the end of the splasher, to the side of the smokebox saddle, horizontally to form the base line. Cut 2 is again a diagonal cut, but vertically downwards to meet cut 1, across the corner of the sandbox top. Cut 3 is across the remaining sandbox part, just above the top of the splasher, until just before the smokebox. The top flap thus made can be prised up with a small screwdriver (or similar), and then cut off with a sharp modelling knife. The remaining sections of sandbox then need to be carefully trimmed away, hopefully leaving the splasher side intact, and a squared off vertical flat smokebox saddle. There should be a rectangular hole. About half is in the footplate, and half in the front part of the splasher top. The first repair section I applied was a piece of plastic card, running from the rear of the splasher hole, to the position of the front of the smokebox extension ring, where it meets the smokebox front (This bing plugged loosely into place to get the measurement.) The height of this plastic section should be the same as the smokebox saddle. The real smokebox saddle has a distinct concave curve to it. This could be ignored, or fiddly job made to get it right (I do not think it worth while, as the splasher and clack valve pipes would also need attention, as both are joined to the boiler!) I used round files, and put a groove into the vertical smokebox saddle side…better than nothing? Patching the holes!... The hole in the footplate is patched from the inside with a piece of plastic card. Making sure that it does not obstruct the wheels… The hole now left, in the splasher, is patched with a pre-curved section of plastic card. If required, careful application of filler may fill any gaps… I was lucky, and managed to retain the splasher lining. Check photos, but most A1X locos did not retain the tank top vents, in ront of the tank filler caps. These have locating pegs that protude into the tank tank tops inside the body. In my case, using a flat item, such as the handle of a craft khife or screwdriver, I simply pushed them out from inside, breaking the glue bond. The holes were patched with plastic card squares on the inside, and plastic rod in the hole, with glue as filler. You may find some plastic sprue or rod of the correct daimeter, which could be glued into the holes, and then trimmed off flush with the tank tops. Or make small circular "blanks" to attach over the holes, like the real thing! The prominent lubricator bowls for the cylinders have been represented with brass handrail knobs, inserted into holes drilled into the smokebox saddle. I will be fitting these to the other (BR) Terrier, which represents KESR No. 3; BR 32670, which had an A1X boiler fitted by the K&ESR, but retained the tank vents, and splasher mounted sandboxes. (It does have a unique bunker extension though!) On these A1 sandboxes, the lubricators are mounted on the front, nearest the smokebox. On A1s the lubricators are in the same place, on the smokebox wing plates. Vacuum, Air or both forms of braking? From photos, Stepney has had the Westinghouse air braking system removed. . (By BR I believe...) http://www.semgonlin...eam/a1x_07.html This loco is preserved in A1X (Re-built) condition, with extension "coal rails" on the bunker, but in Stroudley livery. The Westinghouse Air Brake system and pump has been removed, therefore this loco should only have vacuum pipes on the buffer beams, and the Vacuum ejector pipe on the Left Hand side of the boiler. Dapol and Hornby models seem to all come with this pipe fitted. It is the plastic pipe that runs from the front of the cab to the smokebox. The vacuum brake control would be mounted on the rear of the cab front where the pipe joins the cab. The Westinghouse pump also seems to be a standard fitting, on the right hand cab side. On Vacuum only braked locos, this needs removing. (It is best to see a photo of the real version of your loco to check!) This is held on by two pins in two holes, and can be carefully prised to break the glue bond. The holes then need plugging. Colour matching touch up paint may be a small problem…. Brighton Works, No. 32635 Brighton Works, No. 32635, in the September 1962 photo (Earlier Model Rail article, and on the web.), was dual braked, and retained the Westinghouse pump. From... There is a photo of the Westinghouse pump side on this site...which is of more Brighton interest! http://thebrightonmotivepowerdepots.yolasi...on-loco-men.php This loco also has both Air and Vacuum brake hoses on each buffer beam. The standard fitted brake pipes most closely, in my opinion, resemble Vacuum brake pipes. I fitted two new brake pipes from a batch of spare parts. I think they may be Dapol parts These, being smaller, make very good Air Brake pipes. Couplings and DC fitting. Kadee couplings, or NEM sockets, are still to be fitted. DCC is still to be fitted. DCC is still to be fitted.
  13. sarah


    Hi. Have you considered fitting NEM pockets? Then you have the choice of a lot of coupling types, including Tensiin Lock and Kadee couplings... Parkside make the mountings... Also see here? Regards, Sarah.
  14. The "finished" model... WRENN CCT Modified chassis. BR "Crimson" livery. BR Lettering.from HMRS (PC Models) BR Sheet. Hornby Van C (Untouched save for NEM Kadee Couplings added...) and Wrenn CCT.
  15. The "finished" model... Parkside Kit SR PLV SR Malachite Green "Southern " lettering and number transfers from the. HMRS (PC Models) SR Sheet.